topbar
 
HOME
dot
about us
dot
products
dot
tutorials
dot
where to buy
dot
news at GMP
dot
contact us
bar
 
adss
 

ADSS - All-dielectric Self-supporting Optical Cable Installation

Tools needed to efficiently install and maintain ADSS cable
more info




  Cable Pony Hydraulic ADSS Winch
P/N 70613
The GMP Cable Pony winch offers the constant pulling tension of a double capstan drive and the flexibility of a direct drive drum in one machine.
more info

90° 3 Roller Inside Corner Cable Guide
 

90° 3 Roller Inside Corner Cable Guide
P/N 71563

This guide consists of a curved steel frame that accommodates five 3 roller cable blocks that clamp to the frame. Each block can handle up to three 2-1/2 in. (64 mm) diameter cables.
more info


Corner Blocks
 

Corner Blocks - 45° and 90°new item
P/N 70438 and 70439
These rugged and lightweight corner blocks are used to guide cable and evenly distribute the load on the cable when pulling around corners.
more info


3 Roller Starter Guide Block
 

3 Roller Starter Guide Block
P/N 75268

Used as a starter block during the pulling in of heavy duty cable up to 6 in. (152 mm) diameter as it is pulled from a stationary or moving cable reel.
more info


B Drop Wire Clamp
 

B Drop Wire Clamp
P/N
07380
The wedging action of this aluminum clamp and stainless steel bail holds most sizes of two-conductor drop wire securely, but without damaging the wire covering.
more info


Drop Wire Hook and Strap
 

Drop Wire Hook and Strap
P/N
06530

This galvanized steel wire hook and strap combo is the one to use when you need to install a drop wire clamp
on masonry, or an unexposed drop wire on a non-masonry surface where porcelain insulation is not required.
more info


D Lashing Wire Clamp
 

D Lashing Wire Clamp
P/N
07886

Is perfect for temporary and permanent terminations or grounds, this all steel clamp lets you securely attach two lashing wires or #6 ground wire on any size strand from 1/4 in. to 7/16 in.
more info


E Lashing Wire Clamp
  E Lashing Wire Clamp
P/N 81460

Designed for permanent wire terminations, this clamp has the same hardware, construction and clamping range as our D Clamp (see previous item), but with a one piece stamping formed to let both sides grip the messenger in perfect alignment.
more info

B Lashed Cable Supports
  B Lashed Cable Supports
P/N various

When combined with Cable Spacers, these bands help support and stabilize your cable around poles or other obstructions where the messenger and cable separation doesn’t exceed 3-1/4 in. (83 mm).
more info

C Pull Finder with Case
  C Pull Finder with Case
P/N 84850

Used to determine the pull in feet on corner poles and bisects the corner angle to locate the guy wire or angle.
more info

Protractor Pull Finder
  Protractor Pull Finder
P/N 01190

The Protractor Pull Finder is used to determine the "break" or deflection angle in utility pole lines.
more info

Lashing Wire Grip
 

Lashing Wire Grip
P/N 08605

Used to temporarily fasten lashing wire under tension before placing a permanent clamp like our D or E Lashing Wire Clamps.
more info


Speedigrip Lashing Wire Grip
  Speedigrip Lashing Wire Grip
P/N 01384

A vise type locking grip used to temporarily fasten lashing wire under tension before placing a permanent clamp like our D or E Lashing Wire Clamps.
more info

Roller Type Aerial Cable Guide
 

Roller Type Aerial Cable Guide
P/N 91605

Used to guide and straighten cables as they are pulled into a lashing position from a stationary or moving cable reel.
more info


Overlash Aerial Cable Guide
 

Overlash Aerial Cable Guide
P/N 08007

Used to guide and straighten cables as they are pulled into a lashing position from a stationary or moving cable reel.
more info


70055
 

Single Lashing Aerial Cable Guide
P/N 70055

This guide is economical but durable for new plant construction only.
more info


Fiberglass Handles
 

Wooden Extension Handles
P/N 66000

These useful handles or "lay-up sticks" provide extended reach for all aerial applications including cable placing & tree pruning
more info


Fiberglass Handles
 

Fiberglass Handles
P/N 24194

These fiberglass handles are made of light tubular fiberglass, 1-1/4 in. in diameter
more info


Wire Raising Tool
  Wire Raising Tool
P/N 06355

A good all around tool that gives you the flexibility to place steel strand and aerial telephone wires at the same time.
more info

89600   Electric Capstan Hoist
P/N 89610

This versatile 1,000 lb. capsta is the perfect partner for overhead and underground lifting and pulling applications. The unit is small and lightweight, making it perfect for use in remote and limited access areas.
more info

89600   Manual Chain Hoists
P/N 87268

Our 1-1/2 & 3 ton hoists promise to provide years of dependable service, under the rigorous conditions demanded by the Power Utility & Construction Industries. These hoists feature a time tested and field proven ratchet & pawl design for transmission and distribution applications.
more info

Aerial Handline
 

Aerial Handline
P/N 68590
Discontinued
Used by the craftsperson for raising or lowering tools and materials in OSP aerial work operations.
more info


B Self Locking Aerial Handline
 

B Self Locking Aerial Handline
P/N 08192

Similar to the Aerial Handline, it is intended primarily for one person use and is equipped with a locking mechanism which permits clamping the rope temporarily to hold the load at any desired height to free the hands of the worker.
more info


Utility Handlines
  Utility Handlines
P/N 68593

Available in lengths of either 50 ft. (15 m) or 100 ft. (30 m), this handline is used to raise service drop wires to pole mounted aerial distribution cable plant.
more info

4" Utility Snatch Block
 

4" Utility Snatch Block
P/N 64264
This cadmium-plated snatch block comes with a self locking head and is used for stringing light cable up to
1/2 in. (12 mm) diameter
more info


6 Inch Manila Rope Snatch Block with Latch Hook
 

6 Inch Manila Rope Snatch Block
P/N 64260
This 6" snatch block, made to the Bell System specification, comes with a cast iron sheave & a forged swivel hook that can be rotated 360 degrees
more info


6 Inch Wire Rope Snatch Block with Latch Hook
  6 Inch Wire Rope Snatch Block with Latch Hook
P/N 25798

This 6 in. (152 mm) snatch block comes with a forged swivel latch hook and drop link.
more info

8 in. Wire Rope Snatch Block with Latch Hook
 

discontinued
8 in. Wire Rope Snatch Block
P/N 70628
This 8 in. (203 mm) snatch block comes with a forged swivel hook and drop link. This block is used exclusively with wire rope up to 5/8 in. (16 mm) diameter
more info


6 Inch Wire Rope Snatch Block with Latch Hook
  6 and 8 in. Manila Rope Snatch Block with Latch Hook
P/N 30415 & 30411

These 6 in. (152 mm) and 8 in. (203 mm) snatch blocks come with a forged swivel latch hook and drop link
more info

Lashing Wire Removal Tool
 

B Lashing Wire Removal Tool
P/N 07621

This 32 in. (812 mm) tool makes removing lashing wire from any 3 in. diameter or smaller aerial cable quick and easy.
more info


B Ladder Platform
  B Ladder Platform
P/N 15326

Used to provide a sturdy work platform for the craft person performing work from a ladder.
more info

C Ladder Platform
  C Ladder Platform
P/N 15443

Used to provide a sturdy work platform for the craft person performing work from a ladder. Essentially the same as the B Ladder Platform with the addition of a foot rest.
more info

E Cable Leader
  E Cable Leader
P/N 79600

Prevent your figure 8 (Self Supporting) or pre lashed cable from spiraling while you’re pulling it by using this ingenious tool.
more info

B Chuck
  B Chuck
P/N 08331

This device helps you to easily place self supporting cable using the stationary reel method
more info

F Slack Puller
  F Slack Puller
P/N 08245

Used for deflecting suspension strand temporarily to obtain sufficient slack in aerial cable to facilitate splicing and maintenance operations.
more info

Strand Pullers
  Strand Pullers
P/N 68490

This forged steel unit is used when pulling or tensioning suspension strand.
more info

Standard Cable Block Pusher
  Standard Cable Block Pusher
P/N 70431

Locks onto the strand and push the cable blocks out of the way of the lasher during the cable lashing process. These are especially useful when lashing multiple cables to allow space between the first cable block and the lasher.
more info

Universal Heavy-Duty Cable Block Pusher
 

Universal Heavy-Duty Cable Block Pusher
P/N 70018

Tool that makes the lashing process smoother by maintaining the proper cable lead between the lasher and the cable block.
more info


Cable Pulling Sled
 

Cable Pulling Sled
P/N 70626

Used for aligning two or three cables in our multiple cable block when pulling overhead cable into position prior to lashing.
more info


E ladder Support
  E ladder Support
P/N 86350

Used for supporting the upper end of an extension ladder away from the cable and strand.
more info

B Sheave Support
 

B Sheave Support
P/N 79750

Used with Cable Guards, Cable Spacers, Lashed Cable Supports and a Reinforcing Strap to attach strand and lashed cable to a pole using the suspension bolt where either the upward or downward grade change exceeds 20%.
more info


B Lifting Shackle
  B Lifting Shackle
P/N 07560

Allows attachment of a chain hoist to lashed aerial cable for lifting.
more info

71637
 

Traveling Ground Kit
P/N 71637

Provides a means of maintaining a continuous ground connection to moving conductors such as strand, open wire, or pull line being placed from a stationary reel.
more info


Strand Tensionmeter
  Strand Tensionmeter
P/N 70046

Commonly referred to as a Strand Dynamometer, it is used in tensioning new strand and in measuring the tension in existing strand.
more info


GMP 2000 Cabinet Balcony
  GMP D Cabinet Balcony
P/N 79283

Our newest pole mounted work platform, the GMP D Cabinet Balcony was designed to accommodate the new generation of fiber optic based cabinets as well as the existing line of cross connect cabinets.
more info
bar
GMP reserves the right, without notice, to make changes in equipment design or components as progress in engineering or manufacturing methods may warrant. See our Limited Warranty for more information.
bar
dot dot dot dot dot dot
General Machine Products Co. 3111 Old Lincoln Highway Trevose, PA 19053-4996 USALOGO
Tel: +1.215.357.5500 Fax: +1.215.357.6216 Email: info@GMPtools.com
© 2011 General Machine Products Co., Inc