title
 
HOME
dot
about us
dot
products
dot
tutorials
dot
where to buy
dot
news at GMP
dot
contact us
bar
 
lashing wire  

Stainless Steel Lashing Wire is used in a lasher to lash an aerial cable or combination of cables to a supporting strand.

• A specially controlled annealing process yields a uniform,fine grain structure throughout wire length and cross section for best results

• The GMP lashing wire is packaged as 6 coils per carton for your ordering convenience

• Is available in a 430, 302, and 316 stainless steel alloy


Type 430 Stainless

• Low carbon, 17% chromium wire

• Suitable for general use and in ordinary atmospheric exposure

• Will acquire only a dark surface stain

• Specifically not recommended for use within 25 miles of salt water or industrial operations which emit pollutants


Type 302 Stainless

• 18% chromium, 8% nickel analysis

• This wire has excellent resistance to corrosion from industrial atmospheres

• Its higher tensile strength and breaking load are an added benefit

• A .038 in. diameter Type 302 wire provides strength equal to a .045 in. type 430 wire with better ductility (easier bending and unwinding) and better elongation (less chance of wire breakage from stress)


Type 316 Stainless

• Modified 18-10 analysis containing approximately 2.5% molybdenum

• More resistant to the corrosive action of most chemicals, including chlorides and sulfides, than any other wire

• Particularly resistant to pitting and pin hole corrosion of the kind commonly caused by salt spray

• Its use provides the best insurance against failure under the most severe atmospheric conditions

• All lashing wire is wound in a straight hub configuration to fit all the standard GMP lashers


Buying tip:
When estimating the length of lashing wire required for a cable run, add the following amounts to the length of the run for single lashing.

Add  
For Cables Up to

5%   1 1/2 in. dia.
10%   1 1/2 in. to 3 in. dia.
20%   Over 3 in. dia.
For double lashing, double the quantity

 

P/N
Alloy
Dia.
Ft. Coil
Mtr. Coil
Wt. Coil

71530
430
045
1200
365.8
6.5 lbs.
71531
430
065
650
198.1
7.5 lbs.
71532
430
065
450
137.2
5.3 lbs.
71533
302
045
1200
365.8
6.3 lbs.
71534
316
045
1200
365.8
6.4 lbs.
71535
302
038
1600
487.7
6.3 lbs.
71537
430
.091
350
107.0
6.0 lbs.
71541
316
.065
450
137.2
5.3 lbs.
71542
304
.045
1200
365.8
6.4 lbs.

P/N
Coil Dia.
Coil Width
Coil Pkg.
Note

71530
5.38 in.
1.81 in.
6
1
71531
5.38 in.
1.81 in.
6
3
71532
4.50 in.
1.75 in.
6
2
71533
5.38 in.
1.81 in.
6
1
71534
5.38 in.
1.81 in.
6
1
71535
5.38 in.
1.81 in.
6
1

NOTES:
1. Fits standard C, C2, J2 and Apollo Lasher.
2. Fits G Lasher or C2 and J2 with .065 Modification.
3. For B Lasher only.

For wire types other than shown above consult the factory.

Click on image above for a larger view of our Stainless Steel Lashing Wire
 
Buy online at www.craftworktools.com
bar
dot dot dot dot dot dot
General Machine Products Co. 3111 Old Lincoln Highway Trevose, PA 19053 USA
LOGOTel: +1.215.357.5500 Fax: +1.215.357.6216 Email: info@GMPtools.com

© 2011 General Machine Products Co., Inc